TDS HIPS20MA-7008
HIPS20MA-7008 ?is a compound based on HIPS resin. Excellent & Stable permanent antistatic
property, Good??? impcat & Medium
flow. Suitable for ?IC tray,
injection
molding ?and other ?electronic
products.
HIPS20MA-7008 是一款基于HIPS樹脂的改性塑料；該產品具有優異及穩定的永久抗靜電性能，良好的沖擊韌性和中等流動速率；適用IC托盤、注塑件等電子產品。
Property
?
|
Typical? Properties(1) |
|||
|
Mechanical(2)機械性能 |
Value |
Unit |
Standard |
|
Tensile Stress, break?? 拉伸強度 |
25.0 |
MPa |
ISO 527 |
|
Tensile Strain, break?? 斷裂伸長率 |
10.0 |
% |
ISO 527 |
|
36.0 |
MPa |
ISO 178 |
|
|
Flexural Modulus?????? 彎曲模量 |
2100 |
MPa |
ISO 178 |
|
Impact 沖擊性能 |
Value |
Unit |
Standard |
|
Izod? Impact, notched, ??23°C? 缺口沖擊強度 |
9.0 |
kJ/m2 |
ISO 180-1A |
|
Electrical 電性能 |
Value |
Unit |
Standard |
|
107~109 |
Ω |
IEC 60093 |
|
|
Thermal 熱性能 |
Value |
Unit |
Standard |
|
80 |
℃ |
ISO 75 |
|
|
Physical 物理性能 |
Value |
Unit |
Standard |
|
Density? 密度? ?????????????????????????????????????????? |
1.15 |
g/cm3 |
ISO 1183 |
|
Met Flow Index熔體流動速率 ?(200oC, 10 kg) |
8.0~10.0 |
g/10min |
ISO 1133 |
|
Mold Shrinkage, flow, 24 hrs? 縱向收縮率 |
0.4 – 0.7 |
% |
ISO 294 |
|
Mold Shrinkage, xflow, 24 hrs橫向收縮率 |
0.4 – 0.7 |
% |
ISO 294 |
|
Moisture Absorption ?吸水率 (23oC，24hr) |
0.1 |
% |
ISO 62 |
|
Flame? Characteristics(3)可燃性 |
Value |
Unit |
Standard |
|
Flame Rating阻燃等級 (3.2mm) |
HB |
/ |
UL 94 |
?
?Parameter
|
Injection Molding |
Value |
Unit |
|
Drying? Temperaturez? ??干燥溫度 |
70- 85 |
℃ |
|
Drying ?Time??????????????? ?干燥時間 |
3- 4 |
hrs |
|
Melt? ??Temperature????? ?熔體溫度 |
190- 225 |
℃ |
|
Barrel Temperature?????? ?炮筒溫度 |
190– 240 |
℃ |
|
Mold ?Temperature?????? ?模具溫度 |
40– 60 |
℃ |
|
Back ??Pressure???????????? ??背壓 |
3– 8 |
MPa |
?
THESE PROPERTY VALUES? ARE NOT
INTENDED FOR SPECIFICATION PURPOSES.
(1) Only typical data for selection purposes. Not to
be used for part or tool design.
(2) ?Typical
?values ?only? ?Variations ?within
?normal ?tolerances
?are ?possible
?for ?various
?colors. All values
are ?measured
?after ?at
least 48 hours ?storage at 23℃/50% ?relative
?humidity. All properties, except the melt?volume ?and ?melt
?flow ?rates,
are ?measured ?on
injection ?molded ?samples.
All ?samples ?tested
?under ?ISO?standards .
(3) This rating is not intended to reflect hazards
presented by this or any other material actual fire conditions.
這些屬性值不是用于規范目的的。
（1）僅用于選擇目的的典型數據。 不適用于零件或工具設計。
（2）典型值僅在正常公差內進行各種顏色的變化。 在23℃/50％相對濕度下至少48小時存儲后，所有值均可測量。 除熔體體積和熔體流速外，所有特性均在注射模制樣品上測量。 所有樣品均根據ISO標準進行了測試。
（3）該評級并不旨在反映該或任何其他物質實際火災條件帶來的危害。
注意：以上參數僅用于選用是參考，不用于質量承諾保證，使用時需結合實際工藝進行測試，滿足要求后再使用。